1. 接好鹽水噴霧試驗箱的電源及氣源，電源為單相三線AC220V 50HZ，進氣管外徑為8mm。
2. 打電鹽水噴霧試驗箱電源開關，按設置鍵進行參數設定。NSS實驗時，實驗室溫度為35℃，飽和桶溫度為47℃。AASS及CASS實驗時，實驗室溫度為50℃，飽和桶溫度為63℃。連續鹽霧實驗時須將總實驗時間及噴霧時間設為一致，恒溫計時設為0。間斷式鹽霧實驗時，總計時上設定為總實驗時長，噴霧計時及恒溫計時上設定好噴霧及停噴周期時長。
3. 按下運行鍵，如設備水位不足，報警指示燈會點亮并伴有蜂鳴報警。水位未補足前，設備無輸出。以防電熱器干燒而損壞設備。
4. 同時按下除霧及確定按鍵，可設定時間模式，如S、M、H。每按一次，時間模式改變一次，根據指示燈顯示情況可清楚了解目前時間模式。
5. 實驗中如須查看產品腐蝕狀況，可先按下除霧鍵，設備開始除霧。查看完成后，再次按下除霧鍵，設備再轉為噴霧狀態。
6. 當水位報警燈熄滅后，按下計時鍵，設備進行升溫待機中，溫度達到設定值后，設備自動噴霧，當時間運行完畢，設備自動停機并除霧。或直接按下噴霧，進行噴霧強制運行。噴霧開始后時間同時運行。

以上為廣東愛佩試驗設備有限公司為大家提供的鹽水噴霧試驗箱簡易操作指南，關于更多試驗設備如恒溫恒濕測試箱,高低溫實驗箱,高低溫沖擊試驗箱,氙燈老化試驗箱,紫外老化試驗箱,紫外線老化箱,氙燈試驗箱的簡易操作指南或者更多資料請與我司業務員劉。